根据《会计法》规定，甲公司调整财务数据的行为，对其直接负责的主管人员和其他直接责任人员，可以处

d OSPF.The network 10.100.1.0/24 should not be reachable from the 10.100.9.0/24 network. However, it needs to be reachable from any network within the EIGRP domain. All other networks should be seen in both domains. Which change to router B would accom plish these goals?（）

A. Under the EIGRP process, insert the distribute - list block_net_1 out ospf 1 command.

B. Under the OSPF process, insert the distribute - list block_net_1 in serial1/0 command.

C. Under the EIGRP process, insert the distribute - list block_net_1 in serial1/0 command.

D. Under the OSPF process, insert the distribute - list block_net_1 out eigrp 1 command.

er. AS 65500 is running OSPF as its IGP. Whi ch of the following additions to the configuration is most likely to solve the problem?（）

A. RouterA(config)#ip cef

B. RouterA(config)#ip route 192.168.12.0 255.255.255.252 null 0

C. RouterA(config - router)#ebgp multihop 1

D. RouterA(config - router)#re distribute ospf 1

E. RouterA(config - router)#neighbor 192.168.14.253 next - hop - self

F. RouterA(config - router)#neighbor 192.168.14.253 local - as 65500

om 10.3.0.2, Ethernet0/1, area 0.0.0.1 mismatch area 0.0.0.2 in the header 04:43:19: OSPF: Rcv hello from 10.100.100.3 area 0 from Ethernet0/0 10.1.0.1 04:43:19: OSPF: End of hello processing Refer to the exhibits. What can be done to fix the problem?（）

A. Change router B E0/1 interface to area 0.

B. Change router A interface E0/1 to area 0.0.0.2.

C. Configure the E0/1 i nterfaces of router A and router B to be in area 0.

D. Shut down the E0/1 interfaces in router A and router B as OSPF does not allow "back doors" between areas.

E. Remove the E0/1 interfaces in router A and router B from the OSPF process. Use static rou tes to route data directly from router A to router B to avoid passing data through router C in area 0.

A.Theporthassecurityenabledandhasshutdownduetoasecurityviolation.

B.TheportisoperationalandhasreacheditsconfiguredmaximumallowednumberofMACaddresses.

C.Theportwillallowaccessfor11MACaddressesinadditiontothe3configuredMACaddresses.

D.Ifthenumberofdevicesattemptingtoaccesstheportexceeds11，theportwillshutdownfor20minutes，asconfigured.

ee OSPF neighbors, one connected to each of its three physical interfaces. Which statement is correct about router C?（）

A. It is configured and functioning correctly as an OSPF internal router.

B. It is configured and functioning correc tly as an ABR attached to stub area 4.

C. It is configured and functioning correctly as an ASBR attached to external area 4.

D. It is configured and functioning correctly as an ABR attached to totally stubby area 4.

E. It is not configured correctly to function as specified.

A.PACLscanbeappliedintheinboundoroutbounddirectionofaLayer2physicalinterface.

B.AtLayer2，aMACaddressPACLwilltakeprecedenceoveranyexistingLayer3PACL.

C.WhenyouapplyaportACLtoatrunkport，theACLfilterstrafficonallVLANspresentonthetrunkport.

D.PACLsarenotsupportedonEtherChannelinterfaces.

configuration mode: area 4 stub.Which two things need to be done to finish making area 4 a totally stubby area?（）

A. Apply the area 4 stub command to all routers in the area

B. On the ABR, use the area 4 stub command with the no - summary keyword

C. On the ABR, specify a default cost for the area with the area default - cost command

D. On the ABR, use the default - information originate command to inject a default route into area 4

E. Use the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas

A. Nothing. OSPF will determine the most optimal path for routing data by default.

B. Adjust the hello and dead timers for more rapid detection of link failures.

C. Increase the reference - bandw idth used to calculate the interface default metrics, on all routers in your network.

D. Set the priority values on every broadcast interface to ensure that the designated and backup designated routers are the routers with the most processor and memory resources.

en them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253

A. Store-and-forward switching

B. Microsegmentation

C. Transparent bridging

D. Fragment-free switching

E. Virtual LANs

F. Cut-through switching