Which of the following may lead to family quarrels according to the passage？A．Unawareness

A. Router R1 will advertise connected and summary routes only.

B. The eigrp stub command will automatically enable summarization of routes on R2.

C. Router R1 is configured as a receive - only neighbor and will not send any connected, static, or summary routes.

D. The eigrp stub command prevents all routes except a default route from being advertised to R1.

E. The eigrp stub command prevents queries from being sent from R2 to R1.

F. Router R1 will advert ise connected and static routes. The sending of summary routes will not be permitted.

Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network？ （）

A. both routers R1 and R2

B. router R1

C. router R2

D. none of the routers since they are not configured with static RP

A. Router RTA is the BDR

B. Router RTA is directly connected to interface 192.168.45.1

C. Neighbor 192.168.45.1 has changed its OSPF priority number

D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs

A.As numbers must be changed to match on all the routers.

B.Loopback interface must be configured so a DR is elected.

C.The no auto-summary command is needed on Router A and Router C.

D.Router B needs to have two network statements, one for each connected network.

A.The path of the packets will be R3 to R2 to R1.

B.The path of the packets will be R3 to R1 to R2.

C.The path of the packets will be both R3 to R2 to R1 and R3 to R1.

D.The path of the packets will be R3 to R1

ter R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2？ （）

A. Add the area 1 stub command on routers R1.

B. Add the always keyword to the default - information originate configuration command on router R2.

C. Remov e the default information originate configuration command from router R2 and place it on router R1.

D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

A. Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out inquiring for a second successor to network 10.6.1.0/24.

B. Router R1 can send traffic destined for network 10.6.1.0/24 out of interface FastEthernet0/0.

C. Router R1 is waiting for a reply from the neighb or 10.1.2.1 to the hello message sent out before it declares the neighbor unreachable.

D. Router R1 is waiting for a reply from the neighbor 10.1.2.1 in response to the query sent out about network 10.6.1.0/24.

A. Router R2 will be preferred because it has the higher neighbor IP address.

B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.

C. Router R1 will be preferred because it has a lower local preference.

D. Router R2 will be preferred because it has a higher local preference.

E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.

F. Router R1 will be preferred because it has the lower neighbor IP address.

A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.

B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.

C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.

D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.

E. The Hello parameters on routers R1 and R2 do not m atch.

xchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task？ （）

A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0

B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0

C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0

D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0

E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0

F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0