公司法确认的资本三原则不包括（)。A．资本确定原则B．资本维持原则C．资本不变原则D．资本流动原则

A. The no auto - summary command has not been issued under the EIGRP process on both routers.

B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.

C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.

D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.

eer adds the ip hello - interval eigrp 9 6 command to R1‘s Fa0/0 configuration.Which of the following is true regarding the results from this c hange？（）

A.The show ip eigrp neighbors command on R1 lists the revised Hello timer

B.The show ip eigrp interfaces command on R1 lists the revised Hello timer

C.The R1 - R2 neighborship fails due to Hello timer mismatcH

D.The show ip eigrp interfaces detail command on R1 lists the revised Hello timer

Routers R1 and R2, currently EIGRP neighbors over their Fa0/0 interfaces (respectively),both use EIGRP authentication. Tuesday at 8 p.m. the neighborship fails.Which of the following wo uld not be useful when investigating whether authenticationhad anything to do with the failure？（）

A. debug eigrp packet

B. show key chain

C. show ip eigrp neighbor failure

D. show clock

A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.

B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.

C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.

D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.

E. The Hello parameters on routers R1 and R2 do not m atch.

xchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task？ （）

A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0

B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0

C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0

D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0

E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0

F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0

see the R1 Ethernet subnet on the R4 routing ta ble. You are also not able to see the R4 Ethernet subnet on the R1 routing table.Which configuration change should be made to resolve this issue？ Select the routers where the configuration change will be required, and select the required EIGRP configur ation command(s).（）

A. R1 and R4

B. R2 and R3

C. ip summary-address eigrp 1 10.1.1.0 255.255.255.0 and ip summary - address eigrp 110.2.2.0 255.255.255.0

D. variance 2

E. eigrp stub connected

F. no auto - summary

Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network？ （）

A. both routers R1 and R2

B. router R1

C. router R2

D. none of the routers since they are not configured with static RP

1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers.Which of the following could be used to prevent potential routing loops in this design？（）

A. Using an iBGP mesh inside the Enterprise core

B. Configuring default routes in the Enterprise pointing to both R1 and R2

C. Redistributing BGP routes into the Enterprise IGP

D. Tunneling the packets for the i BGP connection between R1 and R2

d metric weights 0 0 1 0 0 has been added to the EIGRP process so that only the delay metric is used in the path calculations. Which router will R1 select as the successor and feasible successor for Network A？（）

A. R 4 becomes the successor for Network A and will be placed in the routing table. R2 becomes the feasible successor for Network A

B. R4 becomes the successor for Network A and will be included in the routing table. No feasible successor will be selected a s the advertised distance from R2 is higher than the feasible distance

C. R2 becomes the successor and will be placed in the routing table. R4 becomes the feasible successor for Network A

D. R2 becomes the successor and will be placed in the routing t able. No feasible successor will be selected as the reported distance from R4 is lower than the feasible distance

ter R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2？ （）

A. Add the area 1 stub command on routers R1.

B. Add the always keyword to the default - information originate configuration command on router R2.

C. Remov e the default information originate configuration command from router R2 and place it on router R1.

D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.